文72块沙三中油藏天然气驱可行性试验研究

根据文南油田72块沙三中油藏的性质和流体特征，通过室内细管驱替试验和长岩心驱替试验研究，表明注入天然气组成达到一定比例和注入气和温度大于某一临界值，就可以对该油藏进行注烃类气体混相驱，说明注气开发是可行的，并能够提高油藏的采收率。     

顶封封隔管柱的研制与应用

中原油田近年来注水压力不断升高，井况恶化严重，为此开发了顶封封隔管柱，主要阐述了管柱工况受力特点、结构、工作原理及现场使用效果。经现场较大面积的应用证明，各项性能、技术指标达到了现场要求。     

滨南油区注水现状及治理技术

通过对滨南油区注水现状的调查，发现存在的主要问题是水井套管损坏严重和部分水井欠注。文章全面地介绍了套管损坏井治理和攻欠增注工艺技术在现状的应用。     

双河油田特高含水后期开发阶段注采结构调整的实践与应用

针对双河油田的注采结构的现状及特征,通过近几年来在注采结构调整方面的实践与应用,总结出了油田在特高含水后期开发阶段,实现油田控水稳油目标的途径和方法,注水结构调整主要是结合地质特点,减少欠注层段,减少和控制不合理超注井层段和改善吸水剖面;在采液结构调整上,控制高含水层段的注入,加强中低渗透层段的注入,封堵高渗透、高水淹干扰层段,解放动用较差的中低渗透层段,改善平面上采出不平衡的状况。通过实施注采结构调整,双河油田在特高含水后期实现了高效开发。     

Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.     

热平衡流量计研究与应用

依据热平衡方法测流量原理研制的热平衡流量计没有任何可动部件，可靠性大大加强，可以代替常用的浮子流量计和涡轮流量计。该仪器的应用为油水井及注聚合物井的流量测试提供了更为有效的手段和方法。     

Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

注射成形Fe-50%Ni软磁合金的研究

Fe-50 %Ni合金是一种典型的高磁导率和低矫顽力的软磁材料,有着广阔的应用前景.本次实验采用注射成形方法制取Fe-50 %Ni,研究了在注射成形工艺中烧结工艺对最终产品性能及微观组织的影响,并分析了影响产品磁性能的一些主要因素.实验表明,烧结温度的提高和烧结时间的延长能够较好改善产品的力学性能;密度是影响产品磁性能的主要因素,杂质(主要指(C、O、N)的含量和晶粒尺寸对剩磁、磁导率和矫顽力也有较大的影响;通过注射成形方法制取的Fe-50 %Ni,其性能要优于采用传统粉末冶金方法制造的Fe-50 %Ni.     

低渗透油田合理注采井距的确定--以纯41块沙4段低渗透油田为例

以纯41块沙4段低渗透油田为例，从低渗透油田渗流机理出发，分析了造成低渗透油田开发效果差的主要原因。在计算注水井最大井底流压、油井最小井底流压、油水井之间可建立的最大注采压差的基础上，结合室内试验确定的最小启动压力梯度公式计算油田技术极限注采井距，并结合经济合理井距计算结果，确定了油田合理注采井距，并提出了下二步调整方案，实施后取得了显著的效果。该方法为低渗透油田合理井距的确定、提高低渗透油田的开发效果提供了理论依据。     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.